thick film resistor array www.vishay.com for technical questions, cont act: filmresistors.thickfilmchip@vishay.com document number: 31002 252 revision: 13-oct-08 cra06e, cra06s vishay cra06e and cra06s thick film resistor arrays are constructed on a high grade ceramic body with convex terminations. a small package enables the design of high density circuits. the single component reduces board space, component counts and assembly costs. features ? convex terminal array available with either scalloped corners (e version) or square corners (s version) ? wide ohmic range: 10r to 1m0 ? 4 or 8 terminal package with isolated resistors ? lead (pb)-free solder contacts on ni barrier layer ? pure tin plating provides co mpatibility with lead (pb)-free and lead containing soldering processes ? compatible with "restriction of the use of hazardous substances" (rohs) directive 2002/95/ec (issue 2004) notes (1) rated voltage: (2) the power dissipation on the resistor generates a temperature rise against the lo cal ambient, depending on the heat flow suppor t of the printed-circuit board (thermal re sistance). the rates dissipation applies only if the permitted film temperature of 155 c is n ot exceed. notes (3) preferred way for ordering products is by use of the part number (4) please refer to table packaging, see next page standard electrical specifications model circuit power rating p 70 c w limiting element voltage max. v ? temperature coefficient ppm/k tolerance % resistance range e-series cra06e cra06s 03 0.063 50 100 1 10r - 1m0 24 + 96 200 2; 5 24 zero-ohm-resistor available; r max. = 50 m , i max. = 1 a technical specifications parameter unit cra06e & s rated dissipation at 70 c (2) w per element 0.063 limiting element voltage (1) v ? 50 insulation voltage (1 min) v dc/ac peak 100 category temperature range c - 55 to + 155 insulation resistance > 10 9 pr tolera n ce f = 1 % g = 2 % j = 5 % z = 0 j u mper mode l cra06 termi n al style s e special up to 2 digits pi n 04 08 part number and product description part number: cra06s08347k0jta (3) cr a0 6 s 08 347k0jta product description: cra06s 08 03 473 j rt1 e3 08 termi n al cou n t 04 0 8 j tolera n ce f = 1 % g = 2 % j = 5 % z = 0 j u mper circui t 3 = 03 cra06s model cra06s cra06e 03 circuit type 03 473 resista n ce v alue 473 = 47 k 4702 = 47 k 10r0 = 10 100 = 10 000 = 0 j u mper v alu e r = decimal k = tho u sand m = millio n 0000 = 0 j u mpe r e3 lead (p b )-free e3 = p u re tin termination finish rt1 rt1 rt6 first t w o digits (3 for 1 %) are significant. last digit is the m u ltiplier. packagi n g (4) packagi n g (4) ta tc
document number: 31002 for technical questions, contact: filmresistors.th ickfilmchip@vishay.com www.vishay.com revision: 13-oct-08 253 cra06e, cra06s thick film resistor array vishay circuit dimensions available types and ranges model terminal count circuit temperature coefficient tolerance cra06s 04 03 100 ppm/k 1 % 200 ppm/k 5 % ; 2 % 08 03 100 ppm/k 1 % 200 ppm/k 5 % ; 2 % cra06e 08 03 100 ppm/k 1 % 200 ppm/k 5 % ; 2 % packaging model tape width diameter pitch pieces/reel packaging code pa pe r ta p e part number product description cra06 8 mm 180 mm/7" 4 mm 5000 ta rt1 330 mm/13" 4 mm 20 000 tc rt6 - 55 - 25 0 25 50 75 100 125 155 175 120 100 80 60 40 20 0 70 derating ambient temperature in c rated power in % 03 circuit 4 pin 8 pin e- v ersion 103 s- v ersion 1 pin 1 e e a a 103 model pin no# dimensions [in millimeters] laa 1 bb*p t w cra06s 4 1.6 0.38 0.61 0.3 0.3 0.8 0.5 1.5 cra06e 8 3.2 0.38 - 0.3 0.3 0.8 0.5 1.5 cra06s 8 3.2 0.38 0.61 0.3 0.3 0.8 0.5 1.5 tol. 0.15 0.15 0.15 0.15 0.15 0.1 0.1 0.15 solder pad dimensions [in millimeters] model pinscwdpabe cra06s 4 0.8 3.1 0.36 0.44 1.15 cra06e cra06s 8 0.8 3.1 0.36 0.8 0.44 1.15 0.63
www.vishay.com for technical questions, cont act: filmresistors.thickfilmchip@vishay.com document number: 31002 254 revision: 13-oct-08 cra06e, cra06s vishay thick film resistor array notes (1) figures are given for a single element (2) solderability is specified for 2 year s after production or requalification. permitted storage time is 20 years test procedures and requirements en 60115-1 test (clause) conditions of test requirements permissible change ( r / r ) (1) stability class 1 or better stability class 2 or better stability for product types: 10 to 1 m 10 to 1 m cra06e/cra06s resistance (4.5) - 1 % 2 % ; 5 % temperature coefficient (4.8.4.2) 20/- 55/20 c and 20/125/20 c 100 ppm/k 200 ppm/k overload (4.13) u = 2.5 ( p 70 x r ) 1/2 2 x u max. ; 0.5 s (0.25 % r + 0.05 ) (0.5 % r + 0.05 ) solderability (4.17.5) (2) aging 4 h at 155 c, dryheat solder bath method; 235 c; 2 s visual examination good tinning ( 95 % covered) no visible damage resistance to soldering heat (4.18.2) solder bath method; (260 5) c; (10 1) s (0.25 % r + 0.05 ) (0.5 % r + 0.05 ) rapid change of temperature (4.19) 30 min at lct = - 55 c; 30 min at uct = 125 c; 5 cycles (0.25 % r + 0.05 ) (0.5 % r + 0.05 ) damp heat, steady state (4.24) (40 2) c; 56 days; (93 3) % rh (1 % r + 0.05 ) (2 % r + 0.1 ) climatic sequence (4.23) 16 h at uct = 125 c; 1 cycle at 55 c; 2 h at lct = - 55 c; 1 h/1 kpa at 15 c to 35 c; 5 cycles at 55 c u = ( p 70 x r ) 1/2 u = u max. ; whichever is less severe (1 % r + 0.05 ) (2 % r + 0.1 ) endurance at 70 c (4.25.1) u = ( p 70 x r ) 1/2 u = u max. ; whichever is less severe 1.5 h on; 0.5 h off; 70 c; 1000 h (1 % r + 0.05 ) (2 % r + 0.1 ) extended endurance (4.25.1.8) duration extended to 8000 h (2 % r + 0.1 ) (4 % r + 0.1 ) endurance at upper category temperature (4.25.3) uct = 125 c; 1000 h (1 % r + 0.05 ) (2 % r + 0.1 ) applicable specifications ? en 60115-1 generic specification ? en 140400 sectional specification ? en 140401-802 detail specification ? iec 60068-2-x variety of environmental test procedures ? eia 481 packaging of smd components
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
